HFS3 Ver 2 onto 8L Audi S3 1.8 20VT
Hi Richard ,
Greetings, Perhaps you can assist me The ecu in question is ME7.5 Bosch Thus far I have linked the Injector negative to the green wire Map sensor pin 4 to blue wire Red wire to injector + ive All of the above on the ECU cable. On the rear end of the board , PWM - ive linked Multiplier is at 1x IDC is linked Questions : 1. I want to have IDC as the primary , with MPS as the trigger - is this correct ? If so , which do I link on the back and which to I jump on the front ? Thanks |
Re: HFS3 Ver 2 onto 8L Audi S3 1.8 20VT
First of all, is your engine car a direct injection type?
It is better to put the red wire to a "pre-crank live" 12V switch rather the injector (+), it can be quite noisy there. You only need to link the back if you want the system to run 70% IDC / 30% MPS. Otherwise, leave the solder link option. |
Re: HFS3 Ver 2 onto 8L Audi S3 1.8 20VT
Richard ,
\Greetings, Normal port injection using the EV6 injectors if I believe. So I have linked the back on IDC , is that correct ? Yes , I want to run the 70 % IDC/ 30 % MAP . In your expert opinion , would this set up give you better control ? On the top side of the board , IDC is jumped as the trigger . Thank you for your reply |
Re: HFS3 Ver 2 onto 8L Audi S3 1.8 20VT
One more question, are they low impedance injectors? If they are you need to use green harness, but leave the gain as x1.
|
Re: HFS3 Ver 2 onto 8L Audi S3 1.8 20VT
Quote:
These are the normal high impedance injectors , like those found on the 8L A3 / Golf 4 GTI / B6 Audi's ect. |
Re: HFS3 Ver 2 onto 8L Audi S3 1.8 20VT
Quote:
Greetings, any feedback on this ? If I recall , the board came out of the box linked to IDC |
Re: HFS3 Ver 2 onto 8L Audi S3 1.8 20VT
70 % IDC / 30% MAP is more suitable for stretched factory turbo where thermal load is more concentrated at the spool up area. Having more boost related delivery will help combating stress related knock. Often resulted in timing cut and power drop.
The configuration is totally reversible, no harm in trying it out. |
Re: HFS3 Ver 2 onto 8L Audi S3 1.8 20VT
Richard ,
As usual we can count on you for the awnser ! Thanks , So to recap , please confirm I want to use the 30 / 70 (map/idc) so, Rear of Board Only IDC linked or do I link both or unlink both ( I couldnt understand your explanation , sorry) Front of board - independant of the rear , I choose map as the trigger to get injection during mid spool or peak boost. Its a small frame turbo so it spools hard and fast. |
Re: HFS3 Ver 2 onto 8L Audi S3 1.8 20VT
Here are the possible combinations for the under-board solder mods:
1. IDC linked ............. 100% IDC (factory setting) 2. IDC + MPS (solder linked) ............ 70% IDC / 30% MPS 3. Cut IDC link + MPS (solder linked) ............... 100% MPS |
Re: HFS3 Ver 2 onto 8L Audi S3 1.8 20VT
Quote:
|
All times are GMT +1. The time now is 04:14 AM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.