#1
|
|||
|
|||
HFS-5 DDS3 V8 install ?- Turbo Suzuki samurai/tracker TBI
Hey guys. Just finished turbo setup in my samurai and have a question.
Looking to see if the hfs-5 dds3 v8 aquamist kit can be installed in a TBI vehicle. If so..... Where do i get the trigger signal from? The vehicle is an 87 suzuki samurai w/ 93 geo tracker engine/ecm Currently running 5psi/boost 93 octane. Stock geo tracker ecu. Thanks Joe |
#2
|
|||
|
|||
Re: HFS-5 DDS3 V8 install ?- Turbo Suzuki samurai/tracker TBI
Can you tell me the injector reisitanece. If you can obtain a EVXCU ponoput og the unit, I will help you quicker.
__________________
Richard L aquamist technical support |
#3
|
|||
|
|||
Re: HFS-5 DDS3 V8 install ?- Turbo Suzuki samurai/tracker TBI
Quote:
I did find a picture of oem injector driver from a suzuki sidekick which is the same engine and ecm that im running. http://kick-fix.com/ECU/injector-drivers.jpg http://kick-fix.com/ECU/transistors.html Not sure if that helps. I will get actual results tomorrow afternoon if needed. Thanks Last edited by estorvito; 05-11-2010 at 09:11 AM. |
#4
|
|||
|
|||
Re: HFS-5 DDS3 V8 install ?- Turbo Suzuki samurai/tracker TBI
Ok Richard. I checked and
the injector resistance is 1.7 ECU pinout: http://wire-a-zuke.services.officeli...TBI%20Wire.pdf Last edited by estorvito; 05-11-2010 at 11:23 PM. |
#5
|
|||
|
|||
Re: HFS-5 DDS3 V8 install ?- Turbo Suzuki samurai/tracker TBI
anyone?
Everything is installed except for the FIA2 and trigger wire. So far so good. Just not sure where to get this signal from . I dont want to mess anything up. Thanks Joe |
#6
|
|||
|
|||
Re: HFS-5 DDS3 V8 install ?- Turbo Suzuki samurai/tracker TBI
Just got done wiring the kit.
Everything seems to be working like it should. Just need to adjust gauge and dds3v8. I installed everything according to the diagram below. http://www.aquamist.co.uk/forum/gall...S3v8/HFS-5.gif Engine running at idle = Fuel Injection green LED on. Red LED off Engine running rev. engine = Water injection Red LED blinks rapidly but no flow or pump activating. Im thinking it has to do with adj to both controller and gauge? Thanks |
#7
|
|||
|
|||
Re: HFS-5 DDS3 V8 install ?- Turbo Suzuki samurai/tracker TBI
BUMP..... stilll getting no trigger signal.
Anyone else have any ideas before i give up on this system? I really dont want to go back to my old Vari-Cool setup. Thanks Last edited by estorvito; 09-11-2010 at 07:26 PM. |
#8
|
|||
|
|||
Re: HFS-5 DDS3 V8 install ?- Turbo Suzuki samurai/tracker TBI
I have been away for the last two weeks. just catching up. Sorry.
I had a look on the diagram, very nice and clear. I think the injector is driven by a "peak and hold" driver so the signal is extremely wak during the "hold" period. The "peak" period is good but only around 1mS of so. The DDS3v8 will not be able to detect those signals. The green wire of the FIA2 should be connected to pin A17. The HFS-5 consists of a FIA2 module, can you tell me if you can see a purple wire coming out of the FIA2 harness. This wire has an output of 0-5V, representing the 0-100% DC of the fuel injector. Bofore we go any further, I like ot know if the FIA2 is reading the fuel injector correctly first.
__________________
Richard L aquamist technical support |
#9
|
|||
|
|||
Re: HFS-5 DDS3 V8 install ?- Turbo Suzuki samurai/tracker TBI
I have another question, is side kick a addon unit to the original ECU. What is its function since the ECU can drive the stock injector anyway.
Richard
__________________
Richard L aquamist technical support |
#10
|
|||
|
|||
Re: HFS-5 DDS3 V8 install ?- Turbo Suzuki samurai/tracker TBI
Quote:
The kit i have, has no purple wire coming from the FIA2. Only wires are... 2 red, 2 green, 1 black, 1 blue, 1 brown. http://www.aquamist.co.uk/forum/gall...-5+MBC+MAC.pdf Its just like the one above ^^^^ minus the mbc +mac valve. Quote:
Thanks again for all your help. I will check everything tomorrow and post the results. Cheers, Joe Last edited by estorvito; 10-11-2010 at 10:12 AM. |
|
|