waterinjection.info  

Go Back   waterinjection.info > Aquamist specific system Q and A and new products > Aquamist HFS-3 forum

Reply
 
Thread Tools Display Modes
  #11  
Old 05-08-2017, 07:49 PM
KertRe KertRe is offline
Junior Member
 
Join Date: Aug 2017
Location: Estonia
Posts: 8
Default Re: HFS-3 on BMW 535d

Installed everything like said in the manual. Tested the system, pump and everything works, but when start the engine nothing happens.

Tried with injector +/- and now I linked MPS in the ecu(it should activate then manifold pressure detecion? And i connected the blue wire in the grey harness to MAP sensor. Nothing happens, doing this i disconnected injector wires.
I will post the picture of my ecu later.
Reply With Quote
  #12  
Old 06-08-2017, 09:36 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: HFS-3 on BMW 535d

There are several ECUs and wiring diagrams. Until I see the ECU picture, I cannot advise you.

You know who to ask to receive perfect help but since you did not buy from him, you just need to go slowly with me.
__________________
Richard L
aquamist technical support
Reply With Quote
  #13  
Old 10-08-2017, 06:38 PM
KertRe KertRe is offline
Junior Member
 
Join Date: Aug 2017
Location: Estonia
Posts: 8
Default Re: HFS-3 on BMW 535d

Sorry for the delay, its been really busy at work. So here is my ecu

[url=https://flic.kr/p/Xw2duo]
Reply With Quote
  #14  
Old 11-08-2017, 04:48 PM
KertRe KertRe is offline
Junior Member
 
Join Date: Aug 2017
Location: Estonia
Posts: 8
Default Re: HFS-3 on BMW 535d

Would be very thankful if you could make me a simple wiring diagram or sth... Also it would be okey for me to use MAP sensor, but still i havent figure out how to get it to work with it.

Last edited by KertRe; 11-08-2017 at 05:00 PM.
Reply With Quote
  #15  
Old 11-08-2017, 07:09 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: HFS-3 on BMW 535d

Quote:
Originally Posted by KertRe View Post
Sorry for the delay, its been really busy at work. So here is my ecu

[url=https://flic.kr/p/Xw2duo]
I want to see the car's ECU, not the aquamist controller.
__________________
Richard L
aquamist technical support
Reply With Quote
  #16  
Old 21-08-2017, 01:08 PM
KertRe KertRe is offline
Junior Member
 
Join Date: Aug 2017
Location: Estonia
Posts: 8
Default Re: HFS-3 on BMW 535d

Got it work via MPS sensor.

Little more questsions about setting up gain
It seems to me, that i am getting to few water/meth into my intake. Running 2 1.0mm injectors and no restrictor before the FAV.
Is it any use to turn gain switch? Threshold is for the point where it starts to injection, if i understood right. That ei got in the right place.
Reply With Quote
  #17  
Old 25-08-2017, 07:29 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: HFS-3 on BMW 535d

If you run on map sensor + IDC. You need to solder link the MPS pads on the underside of the circuit board.
__________________
Richard L
aquamist technical support
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 11:30 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.