waterinjection.info  

Go Back   waterinjection.info > Aquamist specific system Q and A and new products > Aquamist HFS-4 forum > HFS-4 user manual and wiring diagrams

Reply
 
Thread Tools Display Modes
  #1  
Old 11-03-2012, 12:40 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default BMW Mini-R56 USDM wiring








__________________
Richard L
aquamist technical support
Reply With Quote
  #2  
Old 11-03-2012, 01:37 AM
brightside brightside is offline
Junior Member
 
Join Date: Oct 2011
Location: toronto
Posts: 23
Default Re: BMW Mini-R56 USDM wiring

Thank you! Install starts tomorrow as it will be +12C so the weather is on my side!
Reply With Quote
  #3  
Old 11-03-2012, 06:18 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: BMW Mini-R56 USDM wiring

Please send some install pictures. Check the underboard settings are matching the above drawing just in case.
__________________
Richard L
aquamist technical support
Reply With Quote
  #4  
Old 22-06-2012, 02:52 AM
Scooter09 Scooter09 is offline
Junior Member
 
Join Date: Feb 2012
Location: Mililani, HI
Posts: 13
Default Re: BMW Mini-R56 USDM wiring

Is this wiring diagram applicable to the 2011+ N18 engine?
Reply With Quote
  #5  
Old 23-06-2012, 05:11 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: BMW Mini-R56 USDM wiring

I looked into this briefly. The N18 DME is still made by Siemens I cannot verify the the pin out compatibility.

N14 Engine - N14B16AC (171hp / 177 ft-lbs)
* infinitely variable single VANOS (intake only)
* Siemens DME MED17.2 engine management

N18 Engine - N18B16M0 (181hp / 191 ft-lbs)
* infinitely variable double VANOS
* map-controlled oil pump
* variable valve timing (Valvetronic) with 3-phase servomotor and integrated eccentric shaft sensor
* composite camshaft construction
* new piston design
* Siemens DME MEVD17.2.2
__________________
Richard L
aquamist technical support
Reply With Quote
  #6  
Old 17-09-2012, 06:03 AM
ra2fanatic ra2fanatic is offline
Junior Member
 
Join Date: Sep 2012
Location: El Monte, CA
Posts: 5
Default Re: BMW Mini-R56 USDM wiring

Hi Richard,

Excuse me for being the first post I've ever made on this forum, but I've had my HFS-4 installed for about 3 weeks now and I wanted to know if I have this set up correctly...

I have a '10 MINI Cooper S and currently I'm running without any type of restrictor and a 0.7mm jet. The injectors in in a R56-S is rated at 380cc. I'm also running a 50w/50m. Have I set up my system right?

Here's an image of my board...

Last edited by ra2fanatic; 17-09-2012 at 08:04 AM.
Reply With Quote
  #7  
Old 17-09-2012, 11:24 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: BMW Mini-R56 USDM wiring

Welcome to the forum.

I think you should put in the 0.7mm restrictor.

The setting looks good. if you have any slight mis-fire at high RPM, please up your meth ratio.

Can you tell me where are you putting the jet?
__________________
Richard L
aquamist technical support
Reply With Quote
  #8  
Old 26-09-2012, 06:45 PM
ra2fanatic ra2fanatic is offline
Junior Member
 
Join Date: Sep 2012
Location: El Monte, CA
Posts: 5
Default Re: BMW Mini-R56 USDM wiring

Thanks Richard. I have the jet located just after the MAP sensor. I wanted to place it where Jeff Howerton had placed it in his guide on the hard plastic, but knew it was going to take a bit more work to get the hole set up and it was easier access to place the jet.

I was running a 50m/50w, but now trying a 70m/30w mix.

What would cause the mis-fire at higher RPMs?
Reply With Quote
  #9  
Old 26-09-2012, 07:51 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: BMW Mini-R56 USDM wiring

Did you have a misfire?
__________________
Richard L
aquamist technical support
Reply With Quote
  #10  
Old 26-09-2012, 10:14 PM
ra2fanatic ra2fanatic is offline
Junior Member
 
Join Date: Sep 2012
Location: El Monte, CA
Posts: 5
Default Re: BMW Mini-R56 USDM wiring

I haven't with the current setup.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 08:17 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.