waterinjection.info  

Go Back   waterinjection.info > Injection Theory (what it is and what it does) > Injection Mixtures

Reply
 
Thread Tools Display Modes
  #1  
Old 20-11-2003, 08:49 PM
AaronC AaronC is offline
Junior Member
 
Join Date: Nov 2003
Posts: 2
Default Freezing Point - Best Mixture

Does anyone know what the Freezing point is for a 50/50 Methanol-water mix?

Also, what is the best mixture for performance? 50M/50W? Or would a 25M/75W be better?
Reply With Quote
  #2  
Old 20-11-2003, 09:20 PM
AaronC AaronC is offline
Junior Member
 
Join Date: Nov 2003
Posts: 2
Default

Well, I found some info on this and I thought I would share:

Methanol \ Water Mixtures

Methanol Conc.
Wt. % (Vol.%)---Freezing Point,F(C)---Flash Point, (TCC) F(C)
0(0)--------------- 32(0)--------------- No Flash
10(13)----------- 20(-7)-------------- 130(54)
20(24)----------- 0(-18)-------------- 110(43)
30(35)------------ -15(-26)------------ 95(35)
40(46)------------ -40(-40)------------ 85(29)
50(56)------------ -65(-54)------------ 75(24)
60(66)------------ -95(-71)------------ 70(21)
70(75)------------ -215(<-73)---------- 60(16)
80(83)------------ -225(<-73)---------- 55(13)
90(92)------------ -230(<-73)---------- 55(13)
100(100)---------- -145(<-73)---------- 55(13)



Isopropanol / Water Mixtures

IPA Conc. Vol. % (Wt.)--Freezing Point, F(C)----Flash Point, (TCC) F (C)
0(0)---------------------- 32(0)------------------ No Flash
10(8)--------------------- 25(-4)----------------- 105 (41)
20(17)--------------------- 20(-7)----------------- 85 (29)
30(26)--------------------- 5(-15)----------------- 75 (24)
40(34)--------------------- 0(-18)----------------- 70 (21)
50(44)--------------------- -5(-21)---------------- 65 (18)
60(54)--------------------- -10(-23)--------------- 65 (18)
70(65)-------------------- -20(-29)--------------- 65 (18)
80(76)-------------------- -35(-37)--------------- 65 (18)
90(88)-------------------- -70(-57)--------------- 65 (18)
100(100)------------------ -130(<-73)------------- 53 (12)
Reply With Quote
  #3  
Old 21-11-2003, 03:39 AM
Brad Brad is offline
Member
 
Join Date: Nov 2003
Location: Kansas City, Missouri
Posts: 70
Default

Good information. The mixture for best performance is based on a combination of air fuel ratio and temperature of air being cooled.
If the engine is running 12/1 a/f and has a manifold inlet temp of 200F water is best. If you have a a/f or 13.5/1 with 200F manifold temp them a mixture a methanol would be in order.
If you have a intake manifold temp of less than a 100F a higher consitration of methanol would be useful if you can adjust the fuel ratio.
There is not one ratio that is correct for every application. You will need to test to find you best balance.
__________________
Brad
Reply With Quote
  #4  
Old 22-11-2003, 08:49 PM
AKWRX AKWRX is offline
Member
 
Join Date: Oct 2003
Location: Juneau, Alaska
Posts: 32
Default

The mixture freezing lists above appear to have been sourced from data using chemically pure water. Pure water with no ice nuclei to start the freezing process can be chilled to -40 before changing state to ice. In the atmosphere it is not uncommon to have "super cooled" unfrozen pure water at -15F, or colder in clouds. In the real world, alcohol/water mixtures contain many other contaminates that act as ice nuclei, so the practical freezing points are not nearly as cold as those listed. For example, windshield washer fluid with a 50/50 mix of methanol also has detergents and other particles that serve as ice nuclei. The actual freezing point would be closer to -20F, rather than the listed -65F. I have observed an 80/20 mix of methanol (in a not too clean can) cold soaking outside to have the water visibly start to slush up at only -70F. Also, note that there are typos on the methanol freeze points for the 70, 80, and 90 percent entries (100 degrees off).
Reply With Quote
  #5  
Old 23-11-2003, 10:07 AM
JohnA JohnA is offline
Senior Member
 
Join Date: Nov 2003
Posts: 352
Default

Very useful information Aaron, I was actually looking for it!

I'll use these tables on my website, if you don't mind :lol:
__________________
Cheers,

John

www.max-boost.co.uk
Reply With Quote
  #6  
Old 24-11-2003, 04:11 AM
Forum Admin Forum Admin is offline
Senior Member
 
Join Date: Oct 2003
Posts: 127
Default

Good comprehensive and informative site too.
__________________
Forumadmin
Forumadmin@waterinjection.info
Reply With Quote
  #7  
Old 24-11-2003, 04:35 PM
JohnA JohnA is offline
Senior Member
 
Join Date: Nov 2003
Posts: 352
Default

He he...thanks
__________________
Cheers,

John

www.max-boost.co.uk
Reply With Quote
  #8  
Old 01-04-2004, 10:50 PM
boostm3 boostm3 is offline
Junior Member
 
Join Date: Mar 2004
Location: White Plains, NY
Posts: 7
Default

Heres the problem I found this winter. Here, we had frequent bouts with temperatures well below 20 degrees F. When it got down to near 10, I found that even a 45% methanol mixture, while remaining liquid in its reservoir, would ice up within the 4mm nylon lines. It never burst, since I believe most parts of the system remained liquid, but it wasnt thrilling to see the ice in the nylon lines Ill tell you! I just think that in these very small lines, it can be extremely hard to keep things liquid down below 15 or 20 degrees F. At least, with most of the system remaining liquid, overall there were no problems.
__________________
------
Paul E -
'99 White M3; < 69K miles; Dinan SC kit with 6" RMS crank pulley and water/air Aftercooler: 11 psi-367 SAE rwhp/304 ftlbs; Custom Tuning by Nick G; AA Aquamist Water/Methanol Injection and AA exhaust; Fikse FM-10s;
Reply With Quote
  #9  
Old 06-11-2004, 04:52 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default

This site has a very comprehensive account of all the screen washer mix and freezing point tables.

http://www.ashchem.com/adc/chemicals...=3&is_header=N
__________________
Richard L
aquamist technical support
Reply With Quote
  #10  
Old 08-12-2004, 10:04 PM
masterp2 masterp2 is offline
Senior Member
 
Join Date: Nov 2004
Location: Desert SW, Arizona USA
Posts: 86
Default

Quote:
Originally Posted by boostm3
Heres the problem I found this winter. Here, we had frequent bouts with temperatures well below 20 degrees F. When it got down to near 10, I found that even a 45% methanol mixture, while remaining liquid in its reservoir, would ice up within the 4mm nylon lines. It never burst, since I believe most parts of the system remained liquid, but it wasnt thrilling to see the ice in the nylon lines Ill tell you! I just think that in these very small lines, it can be extremely hard to keep things liquid down below 15 or 20 degrees F. At least, with most of the system remaining liquid, overall there were no problems.
I have just an educated feeling about this. A water/meth solution, loses the meth to evaporation 4x faster than water, so, with time, the solution is weakening, hense the greater likelihood of freezeup. Factor in frequent heatups inside the engine compartment, this is a reasonable explanation.

A small amount (line) will freeze sooner than a large amount as the temps swing. Ice cubes in the freezer are the same way.
__________________
Michael Patton (aka Killerbee)
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 12:11 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.