waterinjection.info  

Go Back   waterinjection.info > Aquamist specific system Q and A and new products > Aquamist HFS-4 forum > HFS-4 user manual and wiring diagrams

Reply
 
Thread Tools Display Modes
  #31  
Old 16-07-2015, 04:37 PM
VegasChef VegasChef is offline
Junior Member
 
Join Date: Jul 2015
Location: Las vegas
Posts: 3
Default Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards

Hi @Richard L;

I Just purchased an aqumist kit for my MS6 and its beautiful so far. I do have a few questions/concerns. Would you be able to update the drawing to include the "user" port wiring. I noticed that it has it for the MS3 but not the MS6. Also the underside of the board is a bit different than the one you have posted. I have the v3.1 so im not sure if this has changed atall. I followed the book as far as setting the Jumpers for a DI motor.

Thanks
Reply With Quote
  #32  
Old 17-07-2015, 07:33 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards

I will work on this this weekend, Wiring will remain the same.

You need the x2.5 jumper configuration.

Richard
__________________
Richard L
aquamist technical support
Reply With Quote
  #33  
Old 23-07-2015, 05:39 PM
VegasChef VegasChef is offline
Junior Member
 
Join Date: Jul 2015
Location: Las vegas
Posts: 3
Default Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards

Hi Richard,

Any updates on wiring? Also had a question about soldering jumpers. Im going to be running 28-30+ PSI do i need to cut/solder (6)
Reply With Quote
  #34  
Old 01-08-2015, 06:44 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards

Update is up, sorry for the delay.

The V3.1 is configured for a 3.5 bar MAP sensor from factory. So no mods.
__________________
Richard L
aquamist technical support
Reply With Quote
  #35  
Old 14-08-2015, 05:59 AM
VegasChef VegasChef is offline
Junior Member
 
Join Date: Jul 2015
Location: Las vegas
Posts: 3
Default Re: Mazdaspeed 6 (update: 1st August 2015 ) SN #12751 on onwards

Hi Richard,

Got everything installed and went to test the system today. Ran into and issue where when I first plug in the trunk the gauge will stay on for 10 seconds or less then I can hear a click inside I'd the controller and then the gauge shuts off.


Any ideas? Thank.
Reply With Quote
  #36  
Old 14-08-2015, 07:13 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Mazdaspeed 6 (update: 1st August 2015 ) SN #12751 on onwards

looks like the one of the following:

- tank sensor is installed upside down,
- no water in the tank
__________________
Richard L
aquamist technical support
Reply With Quote
  #37  
Old 02-06-2017, 08:19 AM
kevin_mps kevin_mps is offline
Junior Member
 
Join Date: Jun 2017
Location: United Kingdom
Posts: 1
Default Re: Mazdaspeed 6 (update: 1st August 2015 ) SN #12751 on onwards

Hi richard.

are you able to get an ecu diagram up for the speed 6 like you have the speed 3?
Reply With Quote
  #38  
Old 02-06-2017, 06:22 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Mazdaspeed 6 (update: 1st August 2015 ) SN #12751 on onwards

The OE ECU only rr wiring diagram for HFS4+ECU?
__________________
Richard L
aquamist technical support
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 09:24 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.