waterinjection.info  

Go Back   waterinjection.info > Aquamist specific system Q and A and new products > Aquamist HFS-3 forum

Reply
 
Thread Tools Display Modes
  #1  
Old 05-06-2017, 12:05 AM
Paulekas Paulekas is offline
Junior Member
 
Join Date: Sep 2016
Location: Chicago
Posts: 10
Default My meth injection stoped working need help pls

Hi richard i have the old verion 1 basically today it stoped working completely so meth gauge is always showing full bars and if you trying to drive it it goes to limp mode on test mode mode it goes up and down in spraying testing mode it sprays is it dead completely or still there is something i could try? Here is pic car on idle car is not spraying just bars are all the way up also here is how my box is set its connected to the injectors




Last edited by Paulekas; 05-06-2017 at 12:09 AM.
Reply With Quote
  #2  
Old 05-06-2017, 07:41 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: My meth injection stoped working need help pls

As much as I like to help but there are no more replacement parts for this system, over 10 years old.

It appeared the flow sensor module (no longer available) has lost a ground wire, this will make the gauge display in full. Check the cable is not broken or shorted along the route to the engine bay.
__________________
Richard L
aquamist technical support
Reply With Quote
  #3  
Old 06-06-2017, 02:57 AM
Paulekas Paulekas is offline
Junior Member
 
Join Date: Sep 2016
Location: Chicago
Posts: 10
Default Re: My meth injection stoped working need help pls

Would newer version of flower sensor would work so i could buy it?
Reply With Quote
  #4  
Old 06-06-2017, 07:47 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: My meth injection stoped working need help pls

The decoder is in the controller now, so it will not work.

I suspect the wiring. Can you measure the voltages of the four top pins on the right side.

Richard
__________________
Richard L
aquamist technical support
Reply With Quote
  #5  
Old 06-06-2017, 04:59 PM
Paulekas Paulekas is offline
Junior Member
 
Join Date: Sep 2016
Location: Chicago
Posts: 10
Default Re: My meth injection stoped working need help pls

I did continuity test from controller to both front sensors wires are fine also all good to the relay and motor in the back what else could i try?
Reply With Quote
  #6  
Old 06-06-2017, 06:00 PM
Paulekas Paulekas is offline
Junior Member
 
Join Date: Sep 2016
Location: Chicago
Posts: 10
Default Re: My meth injection stoped working need help pls

I did meassure top 4 on right side so top 2 12vfs + and - are at 14v when car is running sensor v and c shows 2.9v
Reply With Quote
  #7  
Old 06-06-2017, 09:03 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: My meth injection stoped working need help pls

This is a fault on the top two, it should read 0V.

Take a hi-res picture of the underside of the circuit board. I suspect there is a broken or burn out track. If this is the case, you can repair it quite easily.
__________________
Richard L
aquamist technical support
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 07:03 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.