waterinjection.info  

Go Back   waterinjection.info > Aquamist specific system Q and A and new products > Aquamist HFS-4 forum

Reply
 
Thread Tools Display Modes
  #1  
Old 07-06-2017, 03:44 AM
Gclasse Gclasse is offline
Junior Member
 
Join Date: May 2017
Location: Puerto Rico
Posts: 17
Default Pump Wiring Harness / Level Sensor 2 pin Connector

Hello, just found out that the level sensor 2 pin connector is missing from the used HSF4 kit i bought, can anyone point me where i can source the 2 pin connector that is currently on the kit?? otherwise i will repair with a standard connector it but will have to cut and change the level sensor cable end as well.

IMG_0851.JPG

By the way, i'll be installing in a 996

IMG_0850.JPG
Reply With Quote
  #2  
Old 07-06-2017, 05:44 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Pump Wiring Harness / Level Sensor 2 pin Connector

The connector is made by tyco or amp. You can use any pair of mating connectors for this
__________________
Richard L
aquamist technical support
Reply With Quote
  #3  
Old 08-06-2017, 04:48 AM
Gclasse Gclasse is offline
Junior Member
 
Join Date: May 2017
Location: Puerto Rico
Posts: 17
Default Re: Pump Wiring Harness / Level Sensor 2 pin Connector

Hey Richard! thanks for the Info.. i ended up using a Molex Male / Female connector plus added a little bit more or cable. Continuity checked on all cables and everything in good shape now!

some pics

IMG_0853.JPG

IMG_0854.JPG
Reply With Quote
  #4  
Old 08-06-2017, 08:03 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Pump Wiring Harness / Level Sensor 2 pin Connector

Thank for the update... All good.
__________________
Richard L
aquamist technical support
Reply With Quote
  #5  
Old 09-06-2017, 03:37 AM
Gclasse Gclasse is offline
Junior Member
 
Join Date: May 2017
Location: Puerto Rico
Posts: 17
Default Re: Pump Wiring Harness / Level Sensor 2 pin Connector

Richard, can you tell me the dimensions of all the orings used in the system? Also the one that goes on the right angle fitting as well!

Last edited by Gclasse; 09-06-2017 at 03:48 AM.
Reply With Quote
  #6  
Old 10-06-2017, 08:07 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Pump Wiring Harness / Level Sensor 2 pin Connector

I don't know the size of the o-ring on the right-angle fitting as we don't make them.
There are many o-rings on the system , be a bit more specific.
__________________
Richard L
aquamist technical support
Reply With Quote
  #7  
Old 13-06-2017, 04:01 AM
Gclasse Gclasse is offline
Junior Member
 
Join Date: May 2017
Location: Puerto Rico
Posts: 17
Wink Re: Pump Wiring Harness / Level Sensor 2 pin Connector

Don't worry Richard, Jeff (Howerton engineering) sent me some spare orings on different sizes. All good now!

Quote:
Originally Posted by Richard L View Post
I don't know the size of the o-ring on the right-angle fitting as we don't make them.
There are many o-rings on the system , be a bit more specific.
Reply With Quote
  #8  
Old 13-06-2017, 04:09 AM
Gclasse Gclasse is offline
Junior Member
 
Join Date: May 2017
Location: Puerto Rico
Posts: 17
Default another question on my install

Richard, on my setup (porsche), i decided to install the nozzles at both intercoolers sides. Therefore, I placed the FAV close to driver side intercooler and from there I ran the 4mm tubing to a check valve which was then distributed to each intercooler. Refer to pictures included.

On your experience, Is there a concern with the total length of the 4mm used on this setup?
Attached Images
File Type: jpg IMG_0908.JPG (203.5 KB, 9 views)
File Type: jpg IMG_0909.JPG (209.7 KB, 9 views)
File Type: jpg IMG_0910.JPG (175.6 KB, 8 views)

Last edited by Gclasse; 13-06-2017 at 04:19 AM.
Reply With Quote
  #9  
Old 13-06-2017, 07:03 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Pump Wiring Harness / Level Sensor 2 pin Connector

I suggest putting an inline checkvalve near the far-away jet to stop water siphoning after lift off.
__________________
Richard L
aquamist technical support
Reply With Quote
  #10  
Old 13-06-2017, 08:48 PM
Gclasse Gclasse is offline
Junior Member
 
Join Date: May 2017
Location: Puerto Rico
Posts: 17
Default Re: Pump Wiring Harness / Level Sensor 2 pin Connector

Got it, ordered one from your website today! thanks

Quote:
Originally Posted by Richard L View Post
I suggest putting an inline checkvalve near the far-away jet to stop water siphoning after lift off.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 03:52 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.