waterinjection.info  

Go Back   waterinjection.info > Aquamist specific system Q and A and new products > Aquamist HFS-4 forum

Reply
 
Thread Tools Display Modes
  #41  
Old 24-10-2017, 05:30 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Hfs-4 wiring for Audi B8 s4 3.0 (2009-2013)?

If you probe test point 5, let me know the voltage:
1. pre-crank
2. idling
__________________
Richard L
aquamist technical support
Reply With Quote
  #42  
Old 27-10-2017, 04:48 AM
MiztahSparklez MiztahSparklez is offline
Junior Member
 
Join Date: Jan 2017
Location: San Francisco
Posts: 16
Default Re: Hfs-4 wiring for Audi B8 s4 3.0 (2009-2013)?

Quote:
Originally Posted by Richard L View Post
If you probe test point 5, let me know the voltage:
1. pre-crank
2. idling
Hmm this seems wrong, test point 5 is reading battery voltage. 12v
Reply With Quote
  #43  
Old 27-10-2017, 07:00 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Hfs-4 wiring for Audi B8 s4 3.0 (2009-2013)?

My mistake, test point 17. Sorry.
__________________
Richard L
aquamist technical support
Reply With Quote
  #44  
Old 27-10-2017, 08:51 AM
MiztahSparklez MiztahSparklez is offline
Junior Member
 
Join Date: Jan 2017
Location: San Francisco
Posts: 16
Default Re: Hfs-4 wiring for Audi B8 s4 3.0 (2009-2013)?

.76v accessory
.87-.88v engine idle (edit: seems like it's .94v after a few minutes of idling. My analog boost gauge reads -19.9psi)

Voltage does climb slightly with throttle position.

Last edited by MiztahSparklez; 27-10-2017 at 08:54 AM.
Reply With Quote
  #45  
Old 30-10-2017, 08:06 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Hfs-4 wiring for Audi B8 s4 3.0 (2009-2013)?

This seemed to be a bit on the low side. What is the operating range of the MAP sensor?

a 2-bar MAP sensor should read approximately 1.8V precrank.
a 3-bar map sensor should read approximately 1.3V pre-crank.
__________________
Richard L
aquamist technical support
Reply With Quote
  #46  
Old 30-10-2017, 10:29 AM
MiztahSparklez MiztahSparklez is offline
Junior Member
 
Join Date: Jan 2017
Location: San Francisco
Posts: 16
Default Re: Hfs-4 wiring for Audi B8 s4 3.0 (2009-2013)?

Quote:
Originally Posted by Richard L View Post
This seemed to be a bit on the low side. What is the operating range of the MAP sensor?

a 2-bar MAP sensor should read approximately 1.8V precrank.
a 3-bar map sensor should read approximately 1.3V pre-crank.
Hmm might be part of my problem. The sensor is supposed to be 2.5 bar. The voltage output goes from 0-5v according to the same document I found the bypass information in. Wonder if I tapped the wire for temperature and not pressure. The map sensors have both boost and temperature built in.
Reply With Quote
  #47  
Old 31-10-2017, 09:38 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Hfs-4 wiring for Audi B8 s4 3.0 (2009-2013)?

this makes sense.
__________________
Richard L
aquamist technical support
Reply With Quote
  #48  
Old 13-11-2017, 12:59 AM
MiztahSparklez MiztahSparklez is offline
Junior Member
 
Join Date: Jan 2017
Location: San Francisco
Posts: 16
Default Re: Hfs-4 wiring for Audi B8 s4 3.0 (2009-2013)?

Hey Richard,

I have found that my car actually has yellow with gray stripe wiring for the map sensors post charger. These are found on the right side harness #9 when counting from the right on top and #8 when counting from right on bottom. This is in line with the image below. I was able to test continuity of the wires to verify. I will solder again to one of these wires and test out my activation.

Reply With Quote
  #49  
Old 15-11-2017, 10:04 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: Hfs-4 wiring for Audi B8 s4 3.0 (2009-2013)?

I am confused with you pin location. Two ECU compartments: 60 pin and 94 pin.

Tell me which compartment and pin#. Once located, I will check for you.
__________________
Richard L
aquamist technical support
Reply With Quote
  #50  
Old 15-11-2017, 06:57 PM
MiztahSparklez MiztahSparklez is offline
Junior Member
 
Join Date: Jan 2017
Location: San Francisco
Posts: 16
Default Re: Hfs-4 wiring for Audi B8 s4 3.0 (2009-2013)?

Quote:
Originally Posted by Richard L View Post
I am confused with you pin location. Two ECU compartments: 60 pin and 94 pin.

Tell me which compartment and pin#. Once located, I will check for you.
Pin 86 and pin 75. 86 appears to be passenger side map, 75 is driver side. Both wires are yellow with gray stripe. 94 pin side

I believe the temperature wire was the yellow with light blue stripe (this was reading .8-.9v when at idle).

Last edited by MiztahSparklez; 15-11-2017 at 07:01 PM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 01:34 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.