waterinjection.info  

Go Back   waterinjection.info > Aquamist specific system Q and A and new products > Aquamist HFS-3 forum

Reply
 
Thread Tools Display Modes
  #11  
Old 08-12-2011, 12:03 AM
lil powell lil powell is offline
Junior Member
 
Join Date: Mar 2011
Location: Pearland
Posts: 17
Default Re: 997TT issues?

Quote:
Originally Posted by Richard L View Post
I like top go back to basics... I am very sorry to about your hair loss. Where is pearland?

Can you check harness follow the following colour order.

Pearland is in Houston Texas.

All the wires are correct, do you have the order for the gauge, the shop had to order a longer cable, I just want to make sure it's correct.
Reply With Quote
  #12  
Old 08-12-2011, 03:16 AM
lil powell lil powell is offline
Junior Member
 
Join Date: Mar 2011
Location: Pearland
Posts: 17
Default Re: 997TT issues?

Checked with factory gauge wire and still the bar graph is not lighting up. Also the water level light is green when the kit is on. I have the pin DFS jumped, because when its not jumped both lights turn yellow under boost.
Reply With Quote
  #13  
Old 08-12-2011, 03:38 AM
lil powell lil powell is offline
Junior Member
 
Join Date: Mar 2011
Location: Pearland
Posts: 17
Default Re: 997TT issues?

Reply With Quote
  #14  
Old 08-12-2011, 04:21 AM
Howerton Engineering
Guest
 
Posts: n/a
Default Re: 997TT issues?

Quote:
Originally Posted by lil powell View Post
Ok had a few problems with the kit but have gotten most of them resolved. Right now I am using the biggest restrictor that came with the kit, I have 2 nozzles ran into my Y-pipe. When I go to test it, I only see 1 bar on the gauge in first gear and no bars in any other gear. I have pulled both nozzles to check for clogs, and found none. Then I went a step further and pulled out the brass restrictor thing in the jet itself. With the brass fitting out of the jet, the gauge see's full bars and I can adjust it up in down with the SC knob on the gauge. The problem is now it will spray threw 1 whole gear but when I shift into the next gear it kills the kit. When I let off and roll into the throttle again the gauge bars go up again. I also think since I took the object out of the nozzle it may have sprayed to much because my plugs have possibly fouled out. The fail safe has been turned on and off via DIP switches to see if that was an issue with the car to feel slow at WOT. The tune we run in the car is still able to run without meth so it is not just the car pulling timing or throwing extra fuel. I had the gauge were the bars light up all the way to the middle so I don?t think it was spraying to much. What should I do to get the kit to keep spraying when I get to the next gear and how will I know if I am spraying to much?
Thanks,
Matt
The brass spinner must be in the jet otherwise it will not work correctly.
Reply With Quote
  #15  
Old 08-12-2011, 04:45 AM
lil powell lil powell is offline
Junior Member
 
Join Date: Mar 2011
Location: Pearland
Posts: 17
Default Re: 997TT issues?

Quote:
Originally Posted by Howerton Engineering View Post
The brass spinner must be in the jet otherwise it will not work correctly.
I put it back in and still nothing no bars on the gauge.
Reply With Quote
  #16  
Old 08-12-2011, 09:26 AM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: 997TT issues?

Can you tell me if the gauge displays more bars when SC is turned clockwise.

Question, how many jets are you running?
__________________
Richard L
aquamist technical support
Reply With Quote
  #17  
Old 08-12-2011, 04:36 PM
lil powell lil powell is offline
Junior Member
 
Join Date: Mar 2011
Location: Pearland
Posts: 17
Default Re: 997TT issues?

Quote:
Originally Posted by Richard L View Post
Can you tell me if the gauge displays more bars when SC is turned clockwise.

Question, how many jets are you running?
Nothing changes when I turn the SC, I have tried ever click and still nothing.

Jets? I have 2 Nozzles into my intake. No restrictor in the fav.
Reply With Quote
  #18  
Old 08-12-2011, 08:08 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: 997TT issues?

Please test the SC trimmer as follows:

ignition on:

Put the "PRK" jumper link to "BAR". Twiddle the SC, you should see the bargraph go up and down.

Let me know the result.

I have one more question, can you tell me the serial number of the controller (botton left hand corner)
__________________
Richard L
aquamist technical support
Reply With Quote
  #19  
Old 11-12-2011, 05:08 AM
lil powell lil powell is offline
Junior Member
 
Join Date: Mar 2011
Location: Pearland
Posts: 17
Default Re: 997TT issues?

SN: 10430

I set the jumper on the BAR and it did move the bar graph when I adjusted SC on the gauge.
Reply With Quote
  #20  
Old 11-12-2011, 05:30 PM
Richard L Richard L is offline
Manufacturer sponsor
 
Join Date: Oct 2003
Location: England
Posts: 4,936
Default Re: 997TT issues?

So far, all test results are positive.

The next test will be getting the two jets out of the charge pipe and watch the spray pattern and bars on the gauge, using the "SYS" test jumper. Don't do it more than a few seconds at a time.

PLease post results.
__________________
Richard L
aquamist technical support
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 12:17 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.