#31
|
|||
|
|||
Re: Install HFS-3 on DI engines - any need to connect MAP sensor?
I have sent the flow table reflash instructions.
__________________
Richard L aquamist technical support |
#32
|
|||
|
|||
Re: Install HFS-3 on DI engines - any need to connect MAP sensor?
Ok, i'll try to find the way to make reflashing...
ps: i've posted photos of my install: http://www.aquamist.co.uk/vbulletin/...ead.php?t=2324 |
#33
|
|||
|
|||
Re: Install HFS-3 on DI engines - any need to connect MAP sensor?
Very nice and clean install.
Once you have made a flash cable, I will send you the files to modify the flow table. I have five to six to suit every jet combination.
__________________
Richard L aquamist technical support |
#34
|
|||
|
|||
Re: Install HFS-3 on DI engines - any need to connect MAP sensor?
Hello Richard! I have a question about gauge workout.
In SYS mode (at full flow) it shows 2 bar lights. When accelerating and 1 and 2 gears i see this: http://www.youtube.com/watch?v=QAKGqIaa2_I At 3rd gear: http://www.youtube.com/watch?v=wGKeyseNPwA At other 4-6 gears i saw 2 lights at full throttle. What is it? On the 1 and 2nd gear flow is greater or what?.. Last edited by Cptn_Sol; 28-09-2012 at 06:06 AM. |
#35
|
|||
|
|||
Re: Install HFS-3 on DI engines - any need to connect MAP sensor?
I believe you need to flash in a flow table for a smaller flow. As I remembered you are only running a 0.5mm jet. The standard fl;ow table is cater for 0.8 to 0.1mm.
Until we have it reflashed, it is not easy to determine the actual flow with 2 bar resolution. The HFS-3 tracks fuel flow, your display probably shows what the injector is doing. You can make the following test for me. test pin 16: (what the H3 is seeing) 1. at idle 2. at cruising 3. at WOT
__________________
Richard L aquamist technical support |
#36
|
|||
|
|||
Re: Install HFS-3 on DI engines - any need to connect MAP sensor?
Richard, which programmer should I use to re-flash the EEPROM?
Should it be PIC-specific programmer device or any SPI device is okay? Can I just build SPI programmer on my Arduino microprocessor board and use it? Also, should I unsolder the EEPROM from the mainboard? Sorry for so many questions, but I will do the re-flash for Sergey (Cptn_Sol) and need to know more details.
__________________
Alexey K. I drive Peugeot 207 RC 225 bhp with HFS-3 onboard / tuned ECU |
#37
|
|||
|
|||
Re: Install HFS-3 on DI engines - any need to connect MAP sensor?
I will pm you the details.
__________________
Richard L aquamist technical support |
#38
|
|||
|
|||
Re: Install HFS-3 on DI engines - any need to connect MAP sensor?
Richard, thanks!!
__________________
Alexey K. I drive Peugeot 207 RC 225 bhp with HFS-3 onboard / tuned ECU |
#39
|
|||
|
|||
Re: Install HFS-3 on DI engines - any need to connect MAP sensor?
Just a thought, I posted all the details to Cptn_Sol. I cannot find the email I sent. Can you ask him to forward the same email I sent him?
__________________
Richard L aquamist technical support |
#40
|
|||
|
|||
Re: Install HFS-3 on DI engines - any need to connect MAP sensor?
ok, will ask him!
so the question about SPI programmer was already discussed as well?
__________________
Alexey K. I drive Peugeot 207 RC 225 bhp with HFS-3 onboard / tuned ECU |
|
|