Mazdaspeed 6 (update: 1st August 2015 ) SN #12751 on onwards
http://www.aquamist.co.uk/HFS4/wirin....1-MZS6-v7.gif =================== http://www.aquamist.co.uk/HFS4/wirin.../H4-MS6-v5.gif =================== http://www.aquamist.co.uk/HFS4/wirin...4-MS6-v4ss.gif =================== http://www.aquamist.co.uk/HFS4/wirin.../H4-MS6-v3.gif =================== http://www.aquamist.co.uk/HFS4/wirin.../H4-MS6-v2.gif |
Re: Mazdaspeed 6
Any idea if it will be similar or the same for the MS3?
|
Re: Mazdaspeed 6
|
Re: Mazdaspeed 6
Thanks for the link, I am working on all the drawings this week, it will be posted by soon.
Richard |
Re: Mazdaspeed 6 (update) SN #12091 onwards
The H4 controller has been updated (see serial number). It is no longer necessary to perform one of the under-board modification any more, see old diagram.
For those who has the older version, please contact me for exchange of configuration upgrade. No charge. |
Re: Mazdaspeed 6 (update) SN #12091 onwards
Hi Richard,
I came here from the Mazda Speed forums; I own a 2006 MS6 GT. I am in Houston Texas and want to purchase a kit for this car; it does not have major mods, that is a, SRI, a high flow cat, a balance shaft delete and the Hyper tech tune. What exactly I need to purchase; Regards; silversport |
Re: Mazdaspeed 6 (update) SN #12091 onwards
As far as the water injection system is concerned, you just need a water tank. The HFS-4 has everything for your car.
What is your plan on tuning and power at present? Richard |
Re: Mazdaspeed 6 (update) SN #12091 onwards
I plan to stay as it is at this point; but we do have long hot hummid summers here; thus far let just said I like to keep things clean and cool internally in this car; it has 29K, so the engine still petty tight allthoug I don't granny the car when I by myself,
Thanks, ss |
Re: Mazdaspeed 6 (update) SN #12091 onwards
The system probably quite suitable for your application. It will mirror the fuel flow at any ratio. The consumption is quite low if you just want to keep things cool and minimise carbon build up on the inlet valve.
The system gives excellent atomisation from low to high flow due to its constant line pressure design. The dynamic range is very wide. |
Re: Mazdaspeed 6 (update) SN #12091 onwards
Aqua mist HFS-2 Injection System
Can I run this system on my ms6; I want to go with something solid and upgrade later; if I can list the size nozzle and the tap tool I need; I plan to just run my own tank (windshield washer tank) for now and do away with a truck set up in the near. SilverSport, |
Re: Mazdaspeed 6 (update) SN #12091 onwards
You can certainly run HFS-2 on your car, injection is based on IDC only or 70% IDC/30% manifold pressure.
You need a 1/8NPT tap and a few drop of loctite for the nozzle adaptor. |
Re: Mazdaspeed 6 (update) SN #12091 onwards
OK,
What will be the best way to order; if I can get a link for best results. Thanks, Richard |
Re: Mazdaspeed 6 (update) SN #12091 onwards
Please check your pm.
Richard |
Re: Mazdaspeed 6 (update) SN #12091 onwards
Yes, you can. Make sure it is a HFS2-v2. Ity can be upgraded later.
|
Re: Mazdaspeed 6 (update) SN #12091 onwards
The v2 wiring diagram has been updated to v3. 13th May 2012 |
Re: Mazdaspeed 6 (update) SN #12091 onwards
The v3 wiring diagram has been updated to v4. 8th July 2012 |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
Hi Richard,
I recently bought HFS4. Electric men installed me as WIRING DIAGRAM MS6 v4. And then my boost stay lower than it was. And I understood that my boost control brains of HFS4. Set jets which was included 0.7 mm. when we are working on 100% IDC + gain MAX then red LED turns around 4000 rpm. and the boost is reduced to 0.8 bar it means that jets too small for my configuration. but when I turn on the 100% boost then red LED does not light up. But still, my car is going slower than before the installation HFS4. HFS4 brains cut off boost by themselves . WHY??? tell me which way to IDC, or boost? I bought this WMI HFS due just this working by IDC. power of the car before installation was 320 hp now its about 270-300hp. my modes: FMIC, CAI, full exhaust 3'' + versatuner I plan to get 350 hp thanks |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
What water/methanol mix are you running?
|
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
Quote:
|
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
Quote:
please... i need your help :( |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
Thanks for the update. One more question, how many 0.7mm jets are you running?
It appeared you are injecting too much, putting out the spark or burn rate is slow. I |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
Quote:
|
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
It is interesting a 0.7mm jet will affect your engine so much. Can you try running 80% methanol. This test will identify if the previous 50/50 was loading the ignition system.
Where is your jet installed? |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
Quote:
Ok, I try 80% methanol and what I must to see on dash? |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
How far is the exit of the intercooler to the throttle?
If you are not getting good even distribution to the cylinders, it could cause poor bad burn on one of the cylinders. Is it possible to move the jet further away from the throttle? |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
Quote:
I watch the knock retard and it is not. |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
I really don't know. sol we shall approach this one step at a time. Can you send a picture of the nozzle installation.
|
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
2 Attachment(s)
Quote:
Richard please say something...((( |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
I've just installed one of these kits the question is do you need to wire in the user as the kit was supplied with it, it's a hfs4-v3
|
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
You can follow this drawing:
http://www.aquamist.co.uk/vbulletin/...ead.php?t=2188 |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
Hi @Richard L;
I Just purchased an aqumist kit for my MS6 and its beautiful so far. I do have a few questions/concerns. Would you be able to update the drawing to include the "user" port wiring. I noticed that it has it for the MS3 but not the MS6. Also the underside of the board is a bit different than the one you have posted. I have the v3.1 so im not sure if this has changed atall. I followed the book as far as setting the Jumpers for a DI motor. Thanks |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
I will work on this this weekend, Wiring will remain the same.
You need the x2.5 jumper configuration. Richard |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
Hi Richard,
Any updates on wiring? Also had a question about soldering jumpers. Im going to be running 28-30+ PSI do i need to cut/solder (6) |
Re: Mazdaspeed 6 (update: 8th July 2012 ) SN #12091 onwards
Update is up, sorry for the delay.
The V3.1 is configured for a 3.5 bar MAP sensor from factory. So no mods. |
Re: Mazdaspeed 6 (update: 1st August 2015 ) SN #12751 on onwards
Hi Richard,
Got everything installed and went to test the system today. Ran into and issue where when I first plug in the trunk the gauge will stay on for 10 seconds or less then I can hear a click inside I'd the controller and then the gauge shuts off. Any ideas? Thank. |
Re: Mazdaspeed 6 (update: 1st August 2015 ) SN #12751 on onwards
looks like the one of the following:
- tank sensor is installed upside down, - no water in the tank |
Re: Mazdaspeed 6 (update: 1st August 2015 ) SN #12751 on onwards
Hi richard.
are you able to get an ecu diagram up for the speed 6 like you have the speed 3? |
Re: Mazdaspeed 6 (update: 1st August 2015 ) SN #12751 on onwards
The OE ECU only rr wiring diagram for HFS4+ECU?
|
All times are GMT +1. The time now is 01:48 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.